Schwanheimer fine dosing tips / micro capillary nozzles

One of the most popular adhesives in Germany: connects with and among each other permanently materials such as metal, wood, rubber, GRP, natural and synthetic rubber, ceramics, porcelain, stone, glass, plastic u.v.m. Solvent-free, 1-component adhesive, content 20g. Especially recommended by goldsmiths and jewelery designers, especially when used with Activator Plus (For porous materials such as gypsum, wood, clay, ceramics, leather (shoes), stone, etc.) For bonding where no pressure can be exerted (Model making, jewelry) or very high strengths are required.). Properties: - Quick-drying, quick curing, easy to apply - Suitable for transparent gluing on plexiglas, glass stones such as similis and zirconia, pearls and rubber - Without blooming - the glued area does not leave a white border and does not bloom - Adhesions largely waterproof and resistant to moisture or chemicals - Low viscosity - Temperature resistance: - 55 ° C to + 95 ° C - Stable over several years (TIP: The best storage can be achieved in the refrigerator with the capillary nozzles (Do not store with the screw cap!) Application: The plan - and precisely fitting surfaces of the parts to be bonded must be dry, free of rust, grease, dust and adhesives (pre-cleaning eg with Cleaner Reference 345577) Apply adhesive on one side and spotwise or thinly, by applying pressure to the adhesive surfaces (contact pressure / oxygen removal ) the bonding is initiated, without pressure a correction is instantaneous g Allow the glued parts to rest for a few minutes without load, depending on the material, the final strength varies. It is recommended to carry out self-tests on the suitability. Opening, dosing and storage: Cut the tip of the bottle (drip tip) at the notch. Store vertically. For longer storage, close the drip tip airtight with the micro capillary nozzle (fine dosing tip) or candle wax. Protect adhesives from direct sunlight or heat.

Removes and dissolves adhesives, adhesive residues and stubborn stains (such as red wine, permanent markers etc.) from hands, metal, porcelain, glass, Plexiglas, wood, plastics, clothing, upholstery and carpets - also ideal for pre-cleaning when using industrial adhesive, reference 345576 , Content: 10ml, without expiration date, store in dark place. Application: First check the material for compatibility at a hidden point! Depending on the degree of soiling, apply the dissolver and cleaner and allow to take effect. Remove the dissolved adhesive / stain with a clean cloth with circular movements. If necessary, repeat the process. When removing stains from clothing, it is recommended that you put under absorbent cloth. After finished use, thoroughly wet surfaces with water!

The Turbo for the Industrial Adhesive (Reference 345576): The Activator Plus is a curing accelerator, which is specially adapted to the industrial adhesive. It allows in conjunction with the adhesive fast, crystal clear bonds on very small and / or imperfect surfaces on which no great pressure can be exerted. For bonding of porous and absorbent materials such. Wood, porcelain, leather, ceramics, clay, marble and more. best for. The already given by the adhesive tensile and shear force is increased again with the activator up to 30%. Content: 10ml, without expiration date. Application: Apply the activator on one side with the integrated brush. After a contact time of at least 20 seconds, apply our industrial adhesive to the counterpart (also on one side only) and join the parts together. The adhesive cures immediately upon contact with the activator. Tip: Depending on the application, it is also possible to apply the Activator Plus on one side, for example, to assemble the parts without adhesive and then to let the adhesive run into the break point with the aid of the micro capillary nozzle (fine dosing tip).

One of the most popular adhesives in Germany: connects with and among each other permanently materials such as metal, wood, rubber, GRP, natural and synthetic rubber, ceramics, porcelain, stone, glass, plastic u.v.m. Solvent free, 1K adhesive, content 10g. Especially recommended by goldsmiths and jewelery designers, especially when used with Activator Plus (For porous materials such as gypsum, wood, clay, ceramics, leather (shoes), stone, etc.) For bonding where no pressure can be exerted (Model making, jewelry) or very high strength are required.) Properties: - Fast drying, fast curing, easy processing - Suitable for transparent gluing on plexiglas, glass stones such as similis and zirconia, pearls and rubber - Without blooming - the sticky spot does not leave a white border and does not bloom - Bonding largely waterproof and resistant to moisture or chemicals - low viscosity - Temperature resistance: - 55 ° C to + 95 ° C - Stable over several years (TIP: The best storage can be achieved in the refrigerator with the capillary nozzles! (Do not store with the screw cap!) Application: The flat and precise surfaces of the parts to be bonded must be dry, rust, grease, dust and glue-free (pre-cleaning with, for example, cleaner reference 345577). Adhesive one-sided and spotwise or thinly applied. By pressing the adhesive surfaces (contact pressure / oxygen removal), the bonding is initiated. Without pressure, a correction is possible for a short time. Let the glued parts rest for a few minutes without load, depending on the material, the final strength varies. It is recommended to carry out self-tests on the suitability. Opening, dosing and storage: Cut the tip of the bottle (drip tip) at the notch. Store vertically. For longer storage, close the drip tip airtight with the micro capillary nozzle (fine dosing tip) or candle wax. Protect adhesives from direct sunlight or heat.

The drip tip, which is standard on the adhesive, can be exchanged for snap lock if required. The drip tip can be cleaned in acetone (several hours). Suitable for 10g, 20g and 50g containers.

In conjunction with our industrial adhesive No.100 for bonding and filling cracks, fractures, joints, gaps and holes as well as for bridging, strengthening, modeling and fastening. Replaces any putty without complex mixing and long curing time. Waterproof, temperature and chemical resistant. Can be mechanically worked, sanded, drilled and painted after hardening. Application: Apply industrial adhesive and filler alternately, layer by layer (about 2mm-wise). Do not touch! The adhesive reacts immediately with the filler. Pay attention to good wetting of the filler with our industrial adhesive. Small splices can be easily reinforced with this application (chemical weld). Tip: Cover the holes and corners to be filled with tape as a frame. Content: 30g